In a test experiment on a model aeroplane in wind tunnel, the flow speeds on the upper and lower surfaces of the wings are m s and m s respectively. If the wing area is m, the lift of the wing is _______ N. (Given density of air kg m)
Every Mechanical Properties of Fluids question JEE Main has set, grouped by the idea it tests rather than the order of the syllabus. 193 questions across 9 distinct ideas. Free to read, answer key on every one.
Questions
193
Distinct ideas
9
Share of marks
4.2%
Difficulty
MEDIUM
A chapter is not one subject — it is a handful of procedures the examiner reuses. These are the ones Mechanical Properties of Fluids questions actually test.
61–80 OF 193 · NEWEST FIRST
In a test experiment on a model aeroplane in wind tunnel, the flow speeds on the upper and lower surfaces of the wings are m s and m s respectively. If the wing area is m, the lift of the wing is _______ N. (Given density of air kg m)
A big drop is formed by coalescing 1000 small identical drops of water. If be the total surface energy of 1000 small drops of water and be the surface energy of single big drop of water, the is , where = ________.
Mercury is filled in a tube of radius cm up to a height of cm. The force exerted by mercury on the bottom of the tube is _____ N. (Given, atmospheric pressure Nm, density of mercury kg m, m s, )
A hydraulic press containing water has two arms with diameters as mentioned in the figure. A force of N is applied on the surface of water in the thinner arm. The force required to be applied on the surface of water in the thicker arm to maintain equilibrium of water is ______ N.
A big drop is formed by coalescing 1000 small droplets of water. The ratio of surface energy of 1000 droplets to that of energy of big drop is . The value of is __________
A liquid column of height balances excess pressure of a soap bubble of certain radius. If density of liquid is and surface tension of soap solution is , then diameter of the soap bubble is ______ cm. (if )
Small water droplets of radius 0.01 mm are formed in the upper atmosphere and falling with a terminal velocity of 10 cm/s. Due to condensation, if 8 such droplets are coalesced and formed a larger drop, the new terminal velocity will be _____ cm/s.
A soap bubble is blown to a diameter of 7 cm. 36960 erg of work is done in blowing it further. If surface tension of soap solution is 40 dyne/cm then the new radius is ______ cm. (Take )
Surface tension of a soap bubble is N m. Work done to increase the radius of soap bubble from cm to cm will be: [Take ]
J
J
J
J
Eight equal drops of water are falling through air with a steady speed of 10 cm s. If the drops coalesce, the new velocity is:-
16 cm s
40 cm s
5 cm s
10 cm s
If 1000 droplets of water of surface tension 0.07 N m, having same radius 1 mm each, combine to form a single drop. In the process the released surface energy is- (Take )
J
J
J
J
A fully loaded boeing aircraft has a mass of kg. Its total wing area is m. It is in level flight with a speed of km h. If the density of air is kg m, the fractional increase in the speed of the air on the upper surface of the wing relative to the lower surface in percentage will be ( m s)
Given below are two statements: one is labelled as Assertion A and the other is labelled as Reason R
Assertion A : A spherical body of radius mm having a particular density is falling through a liquid of constant density. The percentage error in the calculation of its terminal velocity is 4%.
Reason R : The terminal velocity of the spherical body falling through the liquid is inversely proportional to its radius. In the light of the above statements, choose the correct answer from the options given below
Both A and R are true and R is the correct explanation of A
Both A and R are true but R is NOT the correct explanation of A
A is true but R is false
A is false but R is true
A hydraulic automobile lift is designed to lift vehicles of mass 5000 kg. The area of cross section of the cylinder carrying load is 250 cm. The maximum pressure the smaller piston would have to bear is [Assume m s]
Pa
Pa
Pa
Pa
Given below are two statements: one is labelled as Assertion A and the other is labelled as Reason R
Assertion A: When you squeeze one end of a tube to get toothpaste out from the other end, Pascal's principle is observed.
Reason R: A change in the pressure applied to an enclosed incompressible fluid is transmitted undiminished to every portion of the fluid and to the walls of its container.
Both A and R are correct but R is NOT the correct explanation of A
A is not correct but R is correct
A is correct but R is not correct
Both A and R is correct and R is the correct explanation of A
A mercury drop of radius m is broken into 125 equal size droplets. Surface tension of mercury is 0.45 N m. The gain in surface energy is:
J
J
J
J
Given below are two statements:
Statement I: Pressure in a reservoir of water is same at all points at the same level of water.
Statement II: The pressure applied to enclosed water is transmitted in all directions equally.
In the light of the above statements, choose the correct answer from the options given below:
Both Statement I and Statement II are false
Statement I is true but Statement II is false
Statement I is false but Statement II is true
Both Statement I and Statement II are true
A small ball of mass and density is dropped in a viscous liquid of density . After some time, the ball falls with a constant velocity. What is the viscous force on the ball?
The height of liquid column raised in a capillary tube of certain radius when dipped in liquid vertically is, cm. If the tube is dipped in a similar manner in another liquid of surface tension and density double the values of liquid , the height of liquid column raised in liquid B would be ______ m.
The figure shows a liquid of a given density flowing steadily in a horizontal tube of a varying cross-section. Cross-sectional area at A is cm, and that at B is mm, if the speed of liquid at B is cm s then is
(Given and are liquid pressures at A and B points. Density kg m. A and B are on the axis of tube)

OTHER PHYSICS CHAPTERS